How To Change A Bathroom Sink Faucet Washer

By | September 21, 2019

How To Change A Bathroom Sink Faucet Washer

If you're like most people, you probably don't think about your bathroom sink faucet washer very often. But if your faucet is leaking, it's a good idea to replace the washer as soon as possible. A leaky faucet can waste a lot of water, and it can also damage your sink or vanity.

Replacing a faucet washer is a relatively easy task that you can do yourself in just a few minutes. Here's a step-by-step guide on how to do it:

Materials You'll Need:

  • New faucet washer
  • Wrench
  • Philips screwdriver
  • Adjustable wrench (optional)

Steps:

  1. Turn off the water supply to the faucet. There should be two shut-off valves under the sink, one for the hot water and one for the cold water. Turn both valves clockwise to close them.
  2. Open the faucet to release any remaining water pressure.
  3. Use a wrench to loosen the packing nut. The packing nut is located at the base of the faucet handle. Turn the packing nut counterclockwise to loosen it.
  4. Remove the handle. Once the packing nut is loose, you should be able to pull the handle straight up to remove it.
  5. Use a Philips screwdriver to remove the screws that hold the faucet stem in place. The faucet stem is the metal piece that connects the faucet handle to the water supply. There are usually two screws that hold the faucet stem in place.
  6. Pull out the faucet stem. Once the screws are removed, you should be able to pull the faucet stem straight out of the faucet body.
  7. Remove the old faucet washer. The faucet washer is a small rubber or plastic disc that sits on the end of the faucet stem. Use your fingers or a pair of pliers to remove the old faucet washer.
  8. Install the new faucet washer. Place the new faucet washer on the end of the faucet stem. Make sure that the washer is facing the correct direction.
  9. Reassemble the faucet. Insert the faucet stem back into the faucet body. Tighten the screws that hold the faucet stem in place. Replace the handle and tighten the packing nut.
  10. Turn on the water supply to the faucet. Check for leaks and tighten the packing nut if necessary.

Tips:

  • If you're not sure what size faucet washer you need, take the old washer to a hardware store and compare it to the new washers.
  • If you have a hard time removing the packing nut, you can use an adjustable wrench to loosen it.
  • Be careful not to overtighten the packing nut. If the packing nut is too tight, it can damage the faucet.

Conclusion:

Replacing a faucet washer is a simple task that can save you money and water. If your faucet is leaking, don't hesitate to replace the washer. It's a quick and easy fix that can help you avoid further damage to your sink or vanity.


Replace A Washer In Leaky Faucet

How To Replace A Washer In Leaky Faucet For Dummies

Replace A Bathroom Sink Faucet

Diy How To Replace A Bathroom Sink Faucet Remove Install

Leaking Tap Learn How To Change A

Leaking Tap Learn How To Change A Washer

Replacing A Bathroom Faucet Fine

Replacing A Bathroom Faucet Fine Homebuilding

How To Change A Faucet Washer

How To Change A Faucet Washer Plumbing By Jake

Replace A Washer In Leaky Faucet

How To Replace A Washer In Leaky Faucet For Dummies

Bathroom Sink Fauced

Can Washer Be Replaced In This Type Of Bathroom Sink Fauced Doityourself Com Community Forums

Leaky Faucet

How To Replace A Washer In An Oldfashioned Leaky Faucet

How To Change A Tap Washer Guide

How To Change A Tap Washer Guide Plumbingforce

Replace A Washer In Leaky Faucet

How To Replace A Washer In Leaky Faucet For Dummies

Leave a Reply

Your email address will not be published. Required fields are marked *